USGlobalSat GPS Forums

Please login or register.

Login with username, password and session length
Advanced search  


Pages: [1]   Go Down

Author Topic: BR-355 F.A.Q.'s  (Read 1976 times)


  • Administrator
  • Jr. Member
  • *****
  • Karma: 0
  • Offline Offline
  • Posts: 59
BR-355 F.A.Q.'s
« on: April 01, 2011, 05:56:33 pm »

1.) Q: What is the PS2 Pin Out of this Unit?
1.) A: Please view the below image for your Pin Out answer

2.) Q: Is this device WAAS enable?
2.) A: Yes, it is WAAS enabled by default if purchased through USGlobalSat and it's Authorized Resellers.

3.) Q: What datum is used?
3.) A: WGS 84

4.) Q: Is this device waterproof?
4.) A: Yes, IPX6.

5.) Q: What's the refresh rate?
5.) A: GGA(1sec), GSA(5sec), GSV(5sec), RMC(1sec),VTG(1sec)

6.) Q: How many satellites are needed for 3-D positioning?
6.) A: A minimum of 4 satellites.

7.) Q: Can I reconfigure receiver? If so, what program?
7.) A: Yes. SirfDemo programming utility.

8.) Q: Can I reconfigure receiver? If so, what program?
8.) A: Yes. SirfDemo programming utility.

9.) Q: Yes. SirfDemo programming utility.
9.) A: Can I reconfigure receiver's Baud-Rate? If so, what program?

10.) Q: Can I reconfigure receiver's NMEA data? If so, what program?
10.) A: Yes. SirfDemo programming utility.

11.) Q: Can I reconfigure receiver for WAAS? If so, what program?
11.) A: Yes. SirfDemo programming utility.

12.) Q: What platforms are supported?
12.) A: Windows/ WinCE/ Mac OS X/ Linux

13.) Q: Is the device WAAS enable by default?
13.) A: Yes, it is WAAS enabled by default if purchased through USGlobalSat and it's Authorized Resellers.

14.) Q: Once set. Is SiRF Binary Protocol a permanent configuration?
14.) A: These settings are temporary until the receiverís internal Super-Cap back-up power supply. Then the receiver will revert back to its original default settings.

15.) Q: Does the current USB driver support Mac OS X Snow Leopard?
15.) A: Yes.

16.) Q: Will my receiver support older NMEA standards?
16.) A: Yes, NMEA 2.0 is backwards compatible with older versions of the protocol. NOTE: If your map software (such as Street Atlas 5) requires data sentence GGA, and your GPS (such as the Magellan 3000) does not output GGA, then they will NOT work together.

17.) Q: What to look for first to know which SiRF firmware version is oldest/newest?
17.) A: Here's a little insight into SiRF version numbers: 2.3.2-GSW2-2.05.024-C1PROD1.0_6A -- the GSW2 means standard SiRFStar II software, and 2.3.2 is the release version number. The 2.05.024 or similar numbers are internal numbers into the engineering data base. C1 is the build variant, a number that varies with each software type, but can relate to flash builds vs. RAM (debug) builds, builds with or without SBAS support (WAAS), builds with one or two serial port support, NMEA or binary protocol default, etc. Prod means this is a released rather than a beta (test) version. 1.00 means the release is without any post-release bug fixes. If there is a letter or letters after the Prod1.00, like Prod1.02b, this would mean that some specific "patches" have been added to provide interim fixes for known bugs. After that, anything on the line is likely added by the manufacturer for internal version control. A number like 0000003729 with XMitac2.0 means this is XTrac 2.0 customized by SiRF for Mitac. In general, an X in the number will imply XTrac software, while GSW2 or GSW3 will indicate standard code for SiRFStar II or SiRFStar III, respectively.

18.) Q: Can we upgrade our SiRF firmware? What' s needed for the process?
18.) A: SiRF provides the new versions to our direct customers, but it is up to them to determine if they want to provide an update mechanism to their end-user customers. While the process is relatively simple, unless there is a hardware way to put the receiver into flash upgrade mode (internal boot mode is our term) there is a chance to get things stuck so you have to send it back to the manufacturer or a repair depot to recover. Further, you must be supplied with a flash programming utility to do the job since you cannot access the flash directly -- you have to go through the ARM processor on the SiRF chipset.

19.) Q: What is the meaning of "baud rate"?
19.) A: Baud rate is really the rate of bit transitions on the serial data link. Since each byte of data adds a start and stop bit, it is 10 bits long, and 38400 baud is 3840 bytes per second. Faster bit rates transfer more bytes per second, i.e., greater bandwidth.

20.) Q: What is trickle mode?
20.) A: The Trickle mode allows for an increase in battery life by putting the GPS module in sleep mode for very short periods of time, such as 300ms per 1s cycle, which will result in a battery life increase of about 40% according to my testing. It can be useful for certain types of applications but there is a hit on performance as the receiver will have to get "back on its feet" when it wakes up. It is especially problematic in difficult reception conditions. Starting with FW 2.3, SiRF has added the "Adaptive Trickle" mode, which as its name implies will adapt the power savings to the conditions of reception. In optimal conditions, I found that the battery life increase amounts to about 30%.
« Last Edit: February 23, 2012, 12:45:07 pm by USG_TECH10 »
Pages: [1]   Go Up

Page created in 0.179 seconds with 19 queries.